• LBI-39039B MD110 Configuration Manual ® EDACS Jessica PBX Gateway. • This manual is published by Ericsson Inc., without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Ericsson Inc., at any time and without notice. Such changes will be incorporated into new editions of this manual. TRUNK LINE CONNECTIONS AND CHARACTERISTICS..12 3.4. MD110 CONFIGURATION DEFINITION..13 4. FEATURE-SPECIFIC MD110 PROGRAMMING..15 4.1.

Cisco 2621 - PBX Interoperability. OUT OF THE USE OR INABILITY TO USE THIS MANUAL. PBX Interoperability: Ericsson MD-110 Rel BC9 PBX with Cisco CallManager. Ericsson md110 pbx spectrum enterprise. Manual or the information contained in it, even if aprisma has been advised of, known. Md110 ericsson.

SITE-BASED CALL ROUTING...15 4.2. ENABLING INBOUND DIGITS FROM MD110 EXTENSIONS..19 5. ADMINISTRATION AND EXAMPLE PROGRAMMING..21 5.1. ADMINISTRATION SUGGESTIONS...21 5.2. SCRIPT FILE....22 5.3. INDIRECT INBOUND RADIO CALLS IN A PBX NETWORK.. DID TO ALL EDACS RADIOS....

DTMF DIALING BY RADIOS... MANUAL DTMF DIALING...75 11.2. RADIO TRANSFERRED DTMF DIALING... 75 APPENDIX A JESSICA PBX GATEWAY QUESTIONNAIRE -- MD110 CONFIGURATION.A-1.

• MD110 configuration requirements. The questionnaire should be completed and provided to the installer of the MD110 at least two weeks in advance of the MD110 installation.

Section 2 contains information on interfaces and requirements, and Section 3 contains additional information and guidelines for the configuration of the MD110. • EDACS radio-to-PBX extension calls are DID calls into the MD110, which are connected to an MD110 extension. A Least-Cost Routing (LCR) code is normally used to direct calls out of the MD110 to the PSTN. The LCR code precedes the dialed number, such as the '9' typically used in North America to access an outside line. The LCR code is used by both radio and MD110 PBX users. • An EDACS-originated call appears to the MD110 as an incoming DID call from an external T1/E1 ISDN trunk. One external T1/E1 ISDN trunk is dedicated to EDACS; a TLU-77/1 (T1) or TLU-76/1 (E1) board in the MD110 provides the trunk interface.

This allows up to 23/30 simultaneous calls to be handled. • Ericsson's standard PC-based communications software is FIOL. It is a DOS-based program included with PC Softdisk (PCSD) software.

PCSD is an Ericsson MD110 file structure emulator for a PC. It allows the MD110 to utilize a PC's hard drive through a small computer systems interface (SCSI). PCSD may also be used to boot the MD110 should its internal hard drive fail. • Software Support Contract Provided by EBC An Ericsson dial-back modem is also needed for remote configuration. Redundancy/Fault Tolerance Since the MD110 provides a redundant control system option, the following could be added for increased reliability: Item Quantity Description LPU-5.

SOFTWARE REQUIREMENTS The MD110 requires the use of BC 8.0 software or later. This software includes the country-specific program units that are provided when ordered for the appropriate country. PC Softdisk software is required for external system backup and software updates. • Either a T1 or an E1 ISDN trunk is used to provide the Jessica internal interface connection between the PI and the MD110. The type of digital trunk to be used depends on the digital interface standards followed by the country of installation. • TRUNK LINE CONNECTIONS AND CHARACTERISTICS A variety of trunk line connections may be used to connect the Jessica MD110 and the external switching equipment.

The MD110 supports the following types of analog and digital trunk line connections for both E1 and T1: •. • Ericsson Business Network (EBN) is required before an MD110 installation. The MD110 installation is performed by EBN or other in-country Ericsson sales office.

Ericsson Inc. Is responsible for working with the customer to provide MD110 configuration definition. This is performed by completing the MD110 configuration questionnaire contained in Appendix A two weeks before the MD110 installation. • LBI-39039B CONFIGURATION This page intentionally left blank. • The MD110 configuration work for routing based on the site of origination and the dialed number is performed as part of the installation by Applications Engineering. Call routing out a trunk can be verified by the CTDEI command at the MD110’s FIOL interface. An example of the use of this command is presented below. Hobbit Five Armies Enhanced more.